top of page

Diaphragm vs Plunger Metering Pumps for Chemical Injection: How to Choose

Writer: Tech Inc
Tech Inc
Nov 7
3 min read

Every chemical injection skid is built around its pumps. Get the pump type wrong and you either pay for capability you never use, or spend the next ten years replacing packing and cleaning up leaks. Both main types are reciprocating, positive-displacement "controlled volume" pumps covered by API 675. The difference is how the stroke reaches the chemical.

How each pump type works

Packed plunger pumps

A plunger reciprocates directly in the chemical, sealed by adjustable packing. The packing is designed to weep slightly, which lubricates it, so a packed plunger pump always has some controlled leakage that must be collected. In return you get simple construction, the highest pressure capability of any metering pump and a low purchase price.

Hydraulic diaphragm pumps

The plunger moves a column of hydraulic oil, which flexes a diaphragm (PTFE or metal). The chemical touches only the diaphragm and the check valves, never a dynamic seal, so the pump is leak-free in normal operation. An internal relief valve on the hydraulic side protects the diaphragm, and many designs include diaphragm-rupture detection.

Mechanical diaphragm pumps

Here the diaphragm is moved directly by a motor-driven or solenoid mechanism. They are compact and economical but limited to low discharge pressures (typically around 20 bar or less), so in oil and gas they suit low-pressure dosing such as water treatment and utility systems rather than wellhead injection.

Pneumatic (gas-driven) plunger pumps

Instrument air or sweet process gas drives a piston that strokes a plunger. They need no electrical power, which made them standard on remote wellpads. The drawback is that gas-driven pumps vent their drive gas, and venting natural gas is increasingly restricted on emissions grounds. That is one reason operators are moving to solar-powered electric injection.

Side-by-side comparison

Feature

Packed plunger

Hydraulic diaphragm

Mechanical diaphragm

Pneumatic plunger

Process leakage

Controlled weep from packing

None in normal operation

None

Controlled weep from packing

Pressure capability

Highest

High

Low

Medium to high

Metering accuracy

API 675 class

API 675 class

Good for low pressure

Lower; depends on gas supply

Main maintenance

Packing adjustment and renewal

Diaphragm and oil changes at intervals

Diaphragm replacement

Seals, gas filters, regulators

Best for

Very high pressure, benign chemicals

Toxic, flammable or costly chemicals

Low-pressure dosing

Sites with no power

Relative cost

Low

Higher

Lowest

Low

What API 675 actually asks for

API 675 sets performance requirements for controlled-volume pumps. The headline figures are steady-state flow accuracy within ±1% of rated capacity over a 10:1 turndown, with linearity and repeatability within ±3%. It also covers materials, testing and documentation. If your company standard calls up API 675, say so in the enquiry: not every metering pump on the market is built or tested to it, and comparing an API 675 pump with a commercial one on price alone is misleading.

Tech Inc. chemical injection skid with duty and standby metering pumps

When a packed plunger pump makes sense

  • Very high injection pressures, such as downhole, wellhead or high-pressure methanol injection.

  • Chemicals that are not acutely toxic, where packing weep can be piped to a closed drain or back to the tank.

  • Budgets where purchase price outweighs maintenance hours, and a maintenance team comfortable adjusting packing.

When a hydraulic diaphragm pump makes sense

  • Toxic or hazardous chemicals such as H2S scavengers, biocides and methanol, where any leak is a safety or environmental event.

  • Expensive chemicals, where a slow leak is money on the floor every day.

  • Abrasive or crystallising products that would wear packing quickly.

  • Sites with zero-emission or leak-free requirements in their HSE rules.

Do not forget the suction side

Reciprocating pumps accelerate the liquid in the suction line on every stroke. Your NPSH calculation must include this acceleration head, not just static head and friction. Keep suction lines short and generously sized, fit a suction pulsation dampener on long runs, and consider heat tracing for chemicals that thicken in winter. Many "pump problems" we are called to investigate turn out to be suction problems.

Plan the spares now

For plunger pumps, hold packing sets and a spare plunger. For hydraulic diaphragm pumps, hold diaphragms, check-valve kits and the correct hydraulic oil. For any pump, hold spare check valves: they are the most frequently replaced component on most injection skids. We list these in every offer so the spares arrive with the skid.

Talk to us about your duty

We build chemical injection skids and multi-head and multi-compartment skids with plunger, hydraulic diaphragm or pneumatic pumps, selected for your chemical and pressure. Send the chemical, flow range and maximum injection pressure to mail@techincresearch.com or call +91 739 749 8656 and we will recommend a pump and return a P&ID and quotation. Before you write the enquiry, use our chemical injection skid specification checklist, and browse all our chemical injection systems.

Comments


bottom of page