top of page

Glass Microfibre and Quartz Filters and Extraction Thimbles: Grades and Uses

Writer: Tech Inc
Tech Inc
10 hours ago
3 min read

At a glance. Glass microfibre filters load heavily, filter fast and survive about 500 °C, so they are the standard for total suspended solids and a fast prefilter. Quartz microfibre filters are purer and survive about 900 °C, so they suit air and stack sampling where the dust is analysed for carbon or metals. Extraction thimbles hold a solid sample during solvent extraction or collect dust inside a stack probe. Tech Inc. supplies glass microfibre filters, quartz microfibre filters and extraction thimbles.

How the three media compare

Property

Glass microfibre

Quartz microfibre

Cellulose (papers and thimbles)

Typical retention in liquids

about 0.7 to 2.7 µm

fine, used mainly for gases

about 2.5 to 25 µm

Maximum temperature

about 500 °C

about 900 °C

about 120 °C

Trace metals and alkali

low

very low

low in ashless grades

Loading capacity

high

high

moderate

Typical uses

TSS, chlorophyll, prefiltration

PM10 and PM2.5, stack sampling, carbon analysis

clarification, gravimetry, Soxhlet extraction

Glass microfibre filters

Binder-free borosilicate fibres form a deep, open mat that holds far more solids than a membrane before blocking. Grades run from about 0.7 µm for fine particles and chlorophyll to about 2.7 µm for high-load liquids. Because the filter survives ignition, it is used for total suspended solids and volatile suspended solids: the filter is dried and weighed, then ignited and weighed again. Pre-washed and pre-weighed circles remove two steps from the method.

Quartz microfibre filters

Quartz fibre has much lower alkali and trace metal content than borosilicate glass and stays stable to about 900 °C. That makes it the filter for ambient particulate samplers when the dust will be analysed for metals or for organic and elemental carbon, and for hot flue gases. Pre-fired grades remove the carbon blank for carbon analysis. Quartz resists acidic gases, but hydrofluoric acid and strong alkali attack it.

Extraction thimbles

  • Cellulose thimbles hold soil, food, polymer or plant samples in a Soxhlet extractor; the solvent cycles through the sample and carries the extract down.

  • Glass fibre thimbles collect dust in stack sampling probes up to about 500 °C.

  • Quartz fibre thimbles serve hotter or more acidic flue gases up to about 900 °C.

Fit matters: a thimble that is too loose lets sample bypass, and one that is too tight tears. Measure the extractor or probe and match the inside diameter and length.

Choosing quickly

  1. Weighing solids from water? Glass microfibre, about 1.2 to 1.6 µm, pre-washed.

  2. Analysing airborne dust for metals or carbon? Quartz microfibre, pre-fired for carbon.

  3. Extracting fat or organics from a solid? Cellulose thimbles, or ashless papers for gravimetry.

  4. Sampling a hot stack? Glass or quartz fibre thimbles, by gas temperature.

  5. Clarifying a liquid before a membrane? Glass microfibre, about 2.7 µm, or a glass-fibre prefilter syringe filter.

Frequently asked questions

Is glass microfibre the same as glass fibre? In laboratory filtration, yes: both mean binder-free borosilicate microfibre filters.

Can quartz filters be used for liquids? They can, but glass microfibre is cheaper and filters liquids just as well; quartz earns its cost at high temperature and for trace analysis.

Do glass fibre filters contain binder? Analytical grades are binder-free, so nothing burns off on ignition.

See also the membrane filter chemical compatibility chart and qualitative filter papers. Send your method and sizes to mail@techincresearch.com for a selection and quotation.

Comments


bottom of page