top of page

Process Note: Seawater RO Pretreatment and SDI Control

Writer: Tech Inc
Tech Inc
8 hours ago
3 min read

At a glance. Seawater reverse osmosis (SWRO) membranes tolerate very little suspended matter, colloids, organics or chlorine. Pretreatment removes these before the high-pressure pumps, and the Silt Density Index (SDI) is the test most plants use to prove it is working. Desalination plants across the world, from the Gulf to the Mediterranean and Australia, judge their pretreatment by SDI, turbidity and how quickly the RO differential pressure climbs.

The pretreatment train

  1. Intake. Open-sea intakes need screens and often chlorination against marine growth. Beach wells and other subsurface intakes give cleaner, steadier water but limited capacity.

  2. Coagulation and flocculation. A ferric salt, sometimes with a polymer, gathers colloids and fine particles into flocs that filters can catch.

  3. Dissolved air flotation (DAF). Used where algal blooms or oil occur, it floats off algae and light solids that would clog the filters.

  4. Media filtration or ultrafiltration. Dual-media gravity or pressure filters remain common. Ultrafiltration (UF) gives a lower, steadier SDI and a physical barrier, at a higher capital cost.

  5. Chemical conditioning. Sodium bisulphite removes residual chlorine, which polyamide membranes cannot tolerate, and antiscalant protects the brine end against scale.

  6. Cartridge filters. Typically around 5 µm, as a last guard in front of the high-pressure pumps. They protect the pumps and membranes but cannot make up for weak upstream filtration.

SDI and the other control measures

  • SDI to ASTM D4189. Membrane makers commonly ask for SDI15 below 5, and most plants aim for below 3. A rising SDI is the earliest warning that pretreatment is slipping.

  • Turbidity. Filtered water is usually held below about 0.2 NTU. Turbidity alone can miss the fine colloids that SDI picks up.

  • ORP and free chlorine. A reading after the bisulphite dose confirms that the membranes see no oxidant.

  • Normalised RO data. Differential pressure, normalised permeate flow and salt passage show whether fouling is reaching the membranes despite good SDI readings.

  • Online and manual SDI. Online analysers track trends around the clock. Manual kits check the analyser and cover test points that have no instrument.

Design points

  • Raw water variability: seasonal algae, storms, red tides and intake depth.

  • Coagulant dose and pH, set by jar tests and adjusted as the seawater changes.

  • Filter loading rate and backwash frequency, which decide filtrate quality.

  • Media or UF: lower capital cost against steadier filtrate and a smaller footprint.

  • Biofouling control, as dissolved organic matter can feed growth on the membranes even when SDI is low.

  • Sampling points before and after each stage, so that problems can be traced to their source.

Common problems

  • Coagulant overdose or carryover, which fouls cartridge filters and membranes with iron.

  • Short cartridge filter life, a sign that the upstream filters are underperforming.

  • Bisulphite dosing errors: too little lets chlorine through, and too much wastes chemicals and can encourage biofouling.

  • Biofouling at the lead elements, shown by a rising differential pressure across the first stage.

  • SDI readings that differ between operators, usually because of differences in test pressure, filter handling or timing.

Where Tech Inc. equipment fits

Tech Inc. supplies the instruments and test rigs used to check and optimise pretreatment: the manual SDI test kit, the Silton 4750 online SDI analyser, turbidity meters, ORP meters and free chlorine meters, the membrane fouling simulator for biofouling studies, and ultrafiltration and RO pilot plants for trials on site water. Full-scale reverse osmosis and ultrafiltration systems are supplied by our sister company, Davey Products.

Related reading

This note is general guidance. Feed-water limits follow the membrane manufacturer's warranty conditions and the plant's own design.

Comments


bottom of page