HIPPS vs a Bigger Flare: When a High-Integrity Pressure Protection System Pays for Itself

When a new well, a higher-pressure source or a debottlenecking project pushes relief loads beyond what the existing flare can take, the default answer is a bigger flare header, a bigger knock-out drum and often a taller stack. A high-integrity pressure protection system (HIPPS) is the alternative. Instead of relieving the overpressure, it stops it at source by closing fast-acting valves before pressure rises above what the downstream equipment can withstand. This guide is for process safety, facilities and project engineers deciding whether HIPPS is worth the extra rigour.
What a HIPPS is
A HIPPS is a safety instrumented system (SIS). In the process industries it is designed and managed to IEC 61511, with its components developed to IEC 61508, and it is commonly required to meet SIL 3, the highest integrity level normally applied in process plants. A typical architecture has three parts:
Sensors: usually three pressure transmitters voting two-out-of-three (2oo3), which tolerates one failed transmitter without either a missed trip or a spurious one.
Logic solver: a safety PLC or a solid-state system rated for the required SIL, separate from the basic process control system.
Final elements: two fast-closing shutdown valves in series, each with its own actuator and solenoid valves, so the system still isolates if one valve fails to close.
On wellhead applications, the HIPPS valves often sit downstream of the wing valve described in our guide to SCSSV, master and wing valve sequencing, protecting a flowline or gathering system rated below the wellhead shut-in pressure.
Where HIPPS is used
Specification breaks, where a high-pressure source, such as a wellhead with a high shut-in pressure, feeds a pipeline or plant rated for less.
Flare-limited plants, where tying in new wells or units would otherwise exceed the existing flare's capacity.
Offshore and space-limited sites, where a larger flare system costs weight and deck space.
Emissions-sensitive sites, where avoiding a relief event avoids a large release.
API 521 recognises that a properly designed high-integrity protection system can be used to reduce relief loads in the design of the disposal system, subject to the rigour that comes with it. The pressure vessel code, the operator's standards and local regulators all have a say, and some still require a relief device as well. Confirm the position against the current edition of each document before you rely on it.
A HIPPS also does not remove the need to understand every overpressure scenario. If a fire case, a blocked outlet inside the plant or a tube rupture still needs relief, the relief devices for those cases remain. HIPPS addresses the specific scenarios it was designed for, typically the high-pressure source upstream.
HIPPS or a bigger flare: the trade-off
Factor | HIPPS | Flare upgrade |
Capital cost | Instrumented package plus valves; often lower when flare changes are extensive | Header, knock-out drum, stack and tie-ins; can be large on brownfield sites |
Footprint and weight | Compact skid and valves | Larger piping and structures |
Emissions | Prevents the release | Relieves to flare when demanded |
Ongoing obligation | Proof testing, bypass control and functional safety management for life | Inspection of relief devices and the flare system |
Effect of a demand | Trip isolates the source | Plant relieves and may keep running |
Project studies | HAZOP, LOPA, SRS and SIL verification | Hydraulic and radiation studies; often a shutdown for tie-ins |
Acceptance | Operator and regulator acceptance needed | Usually conventional |
HIPPS tends to pay when the flare upgrade involves major brownfield work, a plant shutdown to tie in, or extra weight offshore. A bigger flare is often simpler when the added load is modest and the operator has no established functional safety management system.

Design points that decide success
PFDavg: the average probability of failure on demand must fall in the SIL 3 band, at least 0.0001 and less than 0.001 in low-demand mode, calculated for the whole loop with realistic failure data and proof-test intervals.
Closing time against pressure rise: the valves must close before downstream pressure reaches the limit of the protected equipment. Work out how fast pressure rises once the source exceeds the trip point, then budget for transmitter response, logic scan and full valve stroke. Closing times of a few seconds are common, but the calculation sets the number, not a rule of thumb.
Valve selection: the shutdown valves need tight shut-off and a demonstrated closing time at full differential pressure, with actuators sized for the worst case.
Setpoint margins: enough margin between normal operating pressure and the trip point to avoid spurious trips, and between the trip point and the design pressure to allow for closing time.
Proof testing: the test interval feeds directly into PFDavg. Specify how each element will be tested in place, including valve seat leakage.
Partial-stroke testing: moving each valve a small part of its travel online reveals a stuck valve between full proof tests and improves diagnostic coverage.
Bypass management: maintenance overrides must be key-controlled, time-limited, alarmed and logged, with compensating measures under a permit.
Common cause: separate process taps and impulse lines for each transmitter, separate solenoid circuits, and no shared component that one failure could disable.
The lifecycle, step by step
HAZOP identifies the overpressure scenario.
LOPA, or another recognised method, sets the risk reduction the HIPPS must provide, and so its SIL.
The safety requirements specification (SRS) fixes trip points, closing time, voting, proof-test interval and bypass rules.
Detailed design and SIL verification confirm that the architecture and failure data meet the target.
FAT in the factory, then SAT after installation, prove the function end to end.
Operation, proof testing and management of change keep it valid for the life of the plant.
Most of the effort sits in steps 2, 3 and 6. Projects that treat the SRS as a formality usually pay for it at the FAT.
How we support a HIPPS project
We design HIPPS packages in Vaughan, Canada and build them in Chennai, India: transmitters, logic solver, valves, actuators and hydraulic or pneumatic power, assembled and tested as one system. We supply SIL verification calculations and supporting documentation for the client's functional safety assessment, and the FAT is witnessed by the client or a third-party inspector, including measured valve closing times. Related packages include ESD panels and actuator and valve control panels; see also our guide to ESD panel design from cause-and-effect matrix to FAT. Browse our safety control systems and the full oil and gas systems range. Send your SRS or overpressure scenario to mail@techincresearch.com or call +91 739 749 8656 and we will return a P&ID, GA drawing and priced offer.





Comments