top of page

Crossflow Membrane Filtration Explained: TMP, Crossflow Velocity and Fouling

Writer: Tech Inc
Tech Inc
1 day ago
3 min read

At a glance. Crossflow (tangential flow) filtration pumps the feed along the membrane surface while permeate passes through it. The sweeping flow carries rejected material away, so a cake or gel layer stays thin and flux stays steady for long runs. Performance is controlled by two settings: crossflow velocity along the membrane and transmembrane pressure (TMP), usually calculated as the average of feed and retentate pressures minus permeate pressure. Crossflow is used for RO, NF and most UF and MF processes; dead-end filtration suits low-solids feeds and quick laboratory screening.

How crossflow filtration works

The feed enters a channel, flows parallel to the membrane and leaves as retentate (concentrate). A pressure difference across the membrane drives permeate through. Rejected solutes and particles build up near the membrane surface, but the shear from the crossflow continuously moves them downstream, so the layer reaches a steady thickness instead of growing without limit as in dead-end filtration.

Key parameters

Parameter

Definition

Effect

Crossflow velocity

Feed flow ÷ channel cross-section

Higher velocity thins the boundary layer and slows fouling, at the cost of pumping energy

Transmembrane pressure (TMP)

(P feed + P retentate) ÷ 2 − P permeate

Drives flux; above a limiting value extra pressure mainly compacts the fouling layer

Flux

Permeate flow ÷ membrane area (LMH)

Set by TMP, viscosity, temperature and fouling

Recovery

Permeate flow ÷ feed flow

Higher recovery concentrates the feed and raises fouling and scaling risk

Pressure drop

P feed − P retentate

Rises as channels foul; a key trend to watch

Concentration polarisation and fouling

Because the membrane passes solvent and retains solute, the solute concentration at the membrane surface rises above the bulk value: concentration polarisation. It raises osmotic pressure in RO and NF and can push sparingly soluble salts to scale or proteins to form a gel layer in UF. Fouling then adds particles, organics, biofilm or scale on or in the membrane. Higher crossflow velocity, spacers that promote mixing, moderate flux and timely cleaning all limit both effects. See membrane fouling causes and prevention and membrane CIP cleaning.

Crossflow vs dead-end filtration

Aspect

Crossflow

Dead-end

Flow direction

Along the membrane

Straight into the membrane

Cake layer

Limited by shear

Grows continuously

Flux over time

Reaches a steady value

Falls until the filter is cleaned or replaced

Energy

Higher (recirculation pumping)

Lower

Typical use

RO, NF, UF and MF processes, high-solids feeds

Low-solids feeds, cartridge filtration, quick lab screening

Our guide to crossflow vs dead-end test set-ups covers which to use in the laboratory.

Testing crossflow filtration in the laboratory

A crossflow test cell holds a flat-sheet membrane coupon under a defined channel height, with a pump to set crossflow, a back-pressure valve to set TMP, and balances or flow meters on the permeate. Good practice:

  1. Compact the membrane with clean water at the test pressure until flux is stable.

  2. Measure clean-water permeability at 25 °C as the baseline.

  3. Switch to the feed and hold crossflow velocity and TMP constant.

  4. Log flux, TMP, temperature and permeate quality over time.

  5. Clean and re-measure water flux to report flux recovery.

Tech Inc. supplies crossflow test cells, including the 140 cm² crossflow cell, and complete RO and UF test systems.

Frequently asked questions

Is crossflow filtration the same as tangential flow filtration (TFF)?

Yes. TFF is the term used mainly in bioprocessing; crossflow is used in water and industrial filtration.

What crossflow velocity should I use?

It depends on the module and feed; spiral-wound elements and flat-sheet cells are usually run within the element maker's flow limits, and lab cells are set to match the channel velocity of the full-scale module.

Why does flux stop rising when I increase pressure?

Above a limiting flux, extra pressure mainly compresses the polarisation or fouling layer, so flux levels off; operating below that point keeps fouling under control.

Related reading

Comments


bottom of page