top of page

IIT Guwahati Raises Membrane Distillation Efficiency With a Module Co-Developed by Davey Products

Writer: Tech Inc
Tech Inc
12 hours ago
3 min read

At a glance. Researchers at IIT Guwahati built a 16-channel direct contact membrane distillation (DCMD) module with heat recovery and compared single and multistage operation at the same membrane area. The paper states that the module was designed and developed in collaboration with Davey Products, Chennai, Tech Inc.'s sister company in the Davey Group, which also developed the PVDF membrane. Multistage operation gave the most water and the best energy use.

Why this matters

Membrane distillation can treat brines that defeat reverse osmosis, and it runs on low-grade heat. Its weak point is thermal efficiency: heat conducts straight through the membrane instead of driving vapour across it. Longer modules raise output but add cost, floor space and maintenance. Heat recovery and staging are the two levers, and the authors note that no earlier study had compared single and multistage DCMD at the same membrane area with heat exchangers in the loop.

What the team did

Neelam Dutta, Bharat Singh, Senthilmurugan Subbiah and P. Muthukumar built a flat sheet DCMD module with 16 channels, each 250 mm long and 250 mm wide with a 3 mm channel gap. Two heat exchangers recover heat: the first preheats fresh feed with the cold outlet stream, the second heats it further with the reject. They validated a model against experiments, extended it to multistage operation with the same membrane area, and optimised flows and temperatures for gain output ratio (GOR) and specific thermal energy consumption.

Where the Davey Group came in

The DCMD module was designed and developed in collaboration with Davey Products, and Davey Products developed the PVDF membrane: 130 µm thick, with 0.5 µm pores, 70% porosity and a 120° contact angle that still measured 114° after 20 sets of experiments. A membrane that keeps its hydrophobicity through repeated runs is what makes a model validation like this one trustworthy. Davey Products and Tech Inc. belong to the same engineering group, founded in 1990; Tech Inc. builds the membrane distillation test systems and test cells that research groups use for this kind of work.

Results that stand out

  • Multistage operation reached a maximum water productivity of 16.34 LMH.

  • The model matched experiments within 5%: at 353 K and 5 g/L, measured fluxes were 1, 1.6 and 2 LMH at 40, 60 and 80 L/h.

  • Adding heat exchangers raised GOR from 0.35 to 0.45 in a single stage and from 0.4 to 0.6 in multistage operation.

  • After optimisation, GOR reached 0.942 for multistage and 0.882 for single-stage operation.

  • Specific thermal energy consumption fell from 1,100 and 800 kWh/m³ to 711 and 670 kWh/m³ for single and multistage operation.

What it means for your lab

If you are scaling membrane distillation, test staging and heat recovery before you build a longer module. We build lab MD skids and full systems with data acquisition in DCMD, AGMD, SGMD and VMD configurations, with flat sheet test cells and MD membranes to match.

The paper

Dutta, N., Singh, B., Subbiah, S. and Muthukumar, P. (2020). Performance analysis of a single and multi-staged direct contact membrane distillation module integrated with heat recovery units. Chemical Engineering Journal Advances 4, 100055. doi:10.1016/j.ceja.2020.100055

Read the full paper at the publisher for methods, data and figures.

Part of the Research with Tech Inc. series

This post is one of a series on published research made with Tech Inc. equipment and materials. See the full list on Research using Tech Inc. equipment. Next in the series: Anna University and CSIR-CLRI Pair Electro-Oxidation With an MBR on Tannery Effluent.

Published with our equipment? Send the reference to mail@techincresearch.com and we will feature your work. To discuss equipment for a similar study, call +1 (289) 622-1032 or write to mail@techincresearch.com.

Comments


bottom of page